EPSON M128C DRIVERS

After printing, the print head can be very hot. Chapter 2 Using the Printer Operating the Control Panels You can control the basic paper feeding operations of the printer with the buttons on the control panels. You can use the enclosed power switch cover to make sure that the power switch is not accidentally pressed. General problems The lights on the control panel do not come on. There must be no glue on the bottom edge.

Uploader: Fauzragore
Date Added: 2 June 2010
File Size: 70.53 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 3747
Price: Free* [*Free Regsitration Required]

Adjusting epson m128c Paper Near End Sensor The paper near end sensor detects when paper is almost gone by measuring the diameter of the paper roll.

Do not use paper rolls that have the paper glued to the core epson m128c the printer cannot detect the paper end correctly.

Be careful not to touch it. If you are replacing a used ribbon, grasp the end of the tab and epson m128c it from the printer. Appendix A Dip Switch and Paper Near End Settings Although the factory settings are best for almost all uses, if you have m1228c requirements, you can change the DIP switch or paper near end settings.

Epson m128c Cutter Problems Auto cutter problems The auto cutter is jammed.

EPSON TM-HII SERIES OPERATOR’S MANUAL Pdf Download.

See the illustration in epdon 5 for the location of the tab. Turn the check over so that it is face down with the MICR characters on the right-hand side. Using this online operator’s guide. Open the front cover. Page 48 Self mode 1.

Be sure to use paper rolls that meet the epson m128c. The sensor has two settings. If any items are damaged or missing, please contact your dealer epson m128c assistance. Using an incorrect power supply may cause fire or electrical shock. When connecting or disconnecting the power supply epson m128c the printer, make sure that the power epson m128c is not plugged into an electrical outlet.

Otherwise, the paper may rub against the ribbon epson m128c become dirty. By pressing ‘print’ epson m128c you will print only current page.

Pull out a small amount m128cc paper, as shown. Page 56 Normal paper single-ply: Turn off the printer while removing the DIP switch cover to prevent an electric short, which can damage the printer. Page 57 Notes on slip paper The slip paper must be flat, without curls or wrinkles, especially at the top edges.

Never turn the ribbon knob in the opposite direction of the arrow marked on the cassette; otherwise the ribbon cassette may be damaged. They all connect to the connector panel on the bottom epson m128c the printer, which is shown below: Click the Find button if you want to search for a particular term. See Chapter 3 for information on what to do when this epsn comes on. Page 23 Connecting the Display Module The display module connector of the printer can be used epson m128c for epson m128c serial interface.

Close the cutter cover.

Balakong Industrial Area, Cheras. Page of 70 Go. Note the label inside this section that can assist you in replacing the ribbon. epson m128c

Don’t show me this message again. You can use the enclosed power switch cover to make sure that the power switch is not epson m128c pressed. If the problem is not serious, fpson auto cutter returns to its normal position without epson m128c intervention by the user. For a complete listing of topics, see the Contents.

Paper Specifications Paper roll single-ply: If the print head is overheated, the printer will resume printing when the head has cooled usually within two or three epson m128c. Turn the ribbon knob two or three times in the direction of the arrow to take up any slack in epso ribbon. After printing, the print head can eoson very hot. Complete online epson m128c for Acrobat Reader is located in the Help directory for Acrobat Reader.

Epson TM-H5000II series Operator’s Manual

Then turn the epson m128c until epson m128c see in the opening, as shown in the illustration below. When the SLIP light blinks, insert the slip paper into the slip paper inlet using the right edge of the slip paper inlet as a guide.

Turn off the power.